WDTC-01 cnc winder machine precision winding machine Computer controlled bench top transformer or small coil layer winding machines for small coils Computer controlled general transformer and bobbin winder with single winding heads. Recommended for wire gauge 38-9 Features Options/Accessories: • System Enhancement with Foot Pedal Speed Control • Keyless Chuck Adapter – Tooling (1 required) Winding machine...Send Inquiry
WDTC-01 cnc winder machine
precision winder winding machine
Computer controlled bench top transformer or small coil layer winding machines
depending on the ingenuity of the operator. Wires from the finest, to as heavy as number 4 AWG, are handled with equal ease with the two speed ranges and CNC Controller.
now well suited for winding fine wire due to the accuracy of the CNC Controller.
The primary advantage of the new CNC Controller touch screen is that it eliminates most of the trial and error setup time normally encountered while setting up winding parameters.
Proper winding parameters for the Controller can be methodically determined in a short time. A winding job can easily be duplicated for a future job run without having to fuss with adjustments.
The operator will soon appreciate the many convenience features. All controls are on the CNC Controller and the Front Panel within convenient reach of the operator.
Computer controlled general transformer and bobbin winder with single winding heads. Recommended for wire gauge 38-9
0-1200rpm (customizable to 6000rpm)
Winding wire diameter
Winding coil diameter
• System Enhancement with Foot Pedal Speed Control
• Keyless Chuck Adapter – Tooling (1 required)
Winding machine advantages
1. The use of independent bearing design, toothed belt replacement quick and easy.
2. Power-off save winding data, effectively avoid scrap coil.
3. wind to bobbin end side, intelligent deceleration, can fast winding thick wire.
4. Machine can automatic measure out the start winding data and winding width.
5. Can set the spindle climb time, you can set the winding speed up and down when the machine winding.
6. Full-English touch screen display, the operation more convenient and quick.
ENTIRE WINDING PROGRAM ENTERED INTO COMPUTER IN A SIMPLE MANNER
PROGRAMS INCLUDE TURNS, WIRE PITCH AND WINDING SPEED WITH SLOW START AND FINISH
4 QUICKLY CHANGED SPEED TORQUE RANGES UP TO 10,000 RPM FOR WIDE RANGE OF WIRE SIZES
AND TORQUE REQUIREMENTS
DIFFERENT COIL INSTRUCTIONS CAN BE STORED IN COMPUTER MEMORY
ELECTRONIC CONTROLLED TRAVERSE WITH STEPPING MOTOR DRIVE
SIMPLIFIED OPERATOR INSTRUCTION
ELECTRIC BRAKE STANDARD
MANUAL FOR STEP-BY-STEP PROCEDURES
7. Using 32-bit ARM control chip controller, faster computing speed, effectively reducing the cable error.
8. All optical input and output isolation, work stability.
9. The use of Japan imported bearings, belts, Taiwan imported inverter and screw to ensure stable performance.
•ENTIRE WINDING PROGRAM ENTERED INTO COMPUTER IN A SIMPLE MANNER
•PROGRAMS INCLUDE TURNS, WIRE PITCH AND WINDING SPEED WITH SLOW START AND FINISH
•4 QUICKLY CHANGED SPEED TORQUE RANGES UP TO 6,000 RPM FOR WIDE RANGE OF WIRE SIZES
AND TORQUE REQUIREMENTS
•DIFFERENT COIL INSTRUCTIONS CAN BE STORED IN COMPUTER MEMORY AND QUICKLY CALLED
UP BY OPERATOR
•ELECTRONIC CONTROLLED TRAVERSE WITH STEPPING MOTOR DRIVE
•MOST FEATURES INCLUDED AS STANDARD EQUIPMENT AT REMARKABLY LOW COST
•FOOT SWITCH STANDARD
•SIMPLIFIED OPERATOR INSTRUCTION
•ELECTRIC BRAKE STANDARD
•MANUAL FOR STEP-BY-STEP PROCEDURES
Scope of application:
Suitable for ballast winding,high-frequency transformers winding, low-frequency transformers winding, inductors winding and other coils winding.
Instructions for use:
1.Please use 220V ± 10% / 50HZ power supply.
2.Do not place the device in a strong electromagnetic interference environment.
3.Equipment should be -10 ℃ -40 ℃ 95% RH non-condensing environment use.
4.Main circuit board is susceptible to electrostatic damage and damage, do not touch the main circuit board.
5.Do not start and shut down the power frequently, turn off the power after 10 seconds before starting.